Want to know how Husqvarna 350 chainsaw chain replacement is done? The procedure is a piece of cake. Just remove a few screws, take out the cover, and replace the old chain with a new one. Finish the process by putting everything back together. Simple right?
Well, it can be difficult if you don’t know the right way to do all this. But don’t worry, because this article will discuss how it can be done quickly. By the end of this article, you will be able to replace the chain all by yourself.
5 Simple Steps of Husqvarna 350 Chainsaw Chain Replacement
Replacing the chain on Husqvarna 350 chainsaw is a really simple process. If you can follow the easy steps mentioned below, you won’t have the slightest difficulty changing the chain all by yourself.
But before jumping into it, you should have a few things near your reach. These are the tools you need to replace the chain on the Husqvarna chainsaw.
Tools You Need
- A new chain
- A new compatible clutch cover for the chain
- Socket wrench
- Tray
- A clean & thick rag
- Finishing nail
Got the tools? Now let’s get right into it.
Step 1: Preparing The Chainsaw
The first thing you got to do is to place the chainsaw properly. Position it on a flat surface. Make sure you are not putting the machine near any edge.
Now once the chainsaw is properly placed, pull off the boot from the spark plug. This will prevent accidental start-up of the machine.
Lastly, disengage the chain brake to avoid possible accidents. Just push the front handle guard toward the handle.
Step 2: Removing The Chain Cover
Now take the socket wrench, and use it to loosen up the nuts holding the clutch cover. There should be two nuts holding the cover down.
Once the nuts are out of the way, take off the cover. In case the chainsaw is brand new, remove the transportation ring from the bolts as well. But keep it in a safe place. It would be best if you placed it on a tray. You are going to need it soon.
Step 3: Removing The Old Chain
At this point, gently push the guide bar deep into the rear side of the saw. Then lift the chain a little out of the groove. A little force should disengage the chain from the sprocket. Don’t apply too much pressure, or the chain may break. Now slowly pull the chain out of its place and remove it altogether.
Step 4: Clean The Sprockets
It’s your chance to clean the position where the chain will go. Once you close the cover, there won’t be any convenient way to clean it.
The cleaning process is simple. Just use a thick rag to clear out all the oil or clogged gunk from the sprockets. You can use a finishing nail to clean the oil ports. Just scrape around a bit, and everything should be easily cleaned.
Step 5: Installing The New Chain
Now put the new chain over the bar. You have to start from the top of the sprocket. From there, keep working along the top edge of the bar. Run it to the bottom of the sprocket from there. After you are done, the edges of the top edge cutting link should be forward-facing.
Step 6: Wrapping Up
The process is almost done. Now, the only thing left is replacing the clutch cover and putting everything back in its place. Put a new clutch cover in the position. Then tighten up the nuts. It’s okay if the nuts are only finger-tight.
Now use the socket wrench and a flat-head screwdriver to turn the tension adjustment screw. Turn the screws clockwise to tighten it up. Keep tightening it until the chain doesn’t sag anymore at the bottom.
Finally, tighten up the rest of the nuts with the wrench. And now your Husqvarna 350 chainsaw is equipped with a new chain.
A Few Things to Keep in Mind During Replacing Husqvarna 350 Chainsaw Chain
As you can see, changing the Husqvarna 350 chainsaw chain is not difficult at all. But things can go wrong if you are not careful enough. Also, you must ensure the correct fuel mix ratio of the Husqvarna chainsaw for better performance output.
Apart from damaging the device, you may hurt yourself as well. To avoid these undesirable consequences, try to maintain the following suggestions,
- Make sure to place the chainsaw on a flat surface.
- Don’t forget to remove the boot of the spark plug.
- Wear thick rubber gloves to prevent cuts.
- Be careful and slow while pushing the guide bar.
- Lift the chain from its position slowly so it does not get damaged.
- Make sure the edges of the cutting links that are on the top edge are facing forward.
- Always double-check after tightening all screws and nuts.
Keeping these simple points in mind shouldn’t be hard. Try to imply this while working, and the process will go buttery smooth.
This Video Will Help You Too!
Frequently Asked Questions (FAQs)
What size chain does a 350 Husqvarna take?
The ideal size of the chain for a 350 Husqvarna chainsaw is 0.050 gauge for the 18-inch bar.
How do you remove the chain on a Husqvarna 350?
You can remove the chain on your Husqvarna 350 by simply detaching the cover, pushing the guide bar in, and finally lifting the chain from its place.
Can you use an Oregon chain on a Husqvarna chainsaw?
Oregon chain is perfectly compatible with a Husqvarna chainsaw. The ideal chain model for this is the H78 and D72.
Conclusion
Husqvarna 350 chainsaw chain replacement is nothing challenging as you were thinking, right? And now as you know how to perform it, the process shouldn’t even take an hour. Just have all the tools near your reach and maintain the basic safety measures.
As you can see, you don’t have to do much here. This is why this process is the ideal approach. It saves both your money and the chainsaw.
You Can Also Read:
- 4 Husqvarna Boundary Wire Alternative That Makes the Right Fit!
- Who Makes Husqvarna XP Oil? Few Things To Know Before Buying
- Husqvarna Spark Plug Chart For Chainsaw, Trimmer & Mower
- Husqvarna 550 XP Problems You Should Be Aware of
Was it helpful?
If it has a motor Jason has a pretty good idea about how it works. Jason graduated in Automotive Mechanics Technology from Bishop State in 1992. After working on vehicles for 11 years he made the transition to selling tractors and lawn care vehicles. Currently, Jason writes and edits much of our content as he transitions into retirement with his lovely wife, Shelley.